Solid Solutions
A solid solution may be formed when impurity atoms are added to a solid, in which case the original crystal structure is retained and no new phases are formed. • Substitutional solid solutions: impurity atoms substitute for host atoms, and appreciable solubility is possible only when atomic diameters and electronegativities for both atom types are similar, when both elements have the same crystal structure, and when the impurity atoms have a valence that is the same as or less than the host material.…
Kinetics of nucleation and growth
From a micro structural standpoint, the first process to accompany a phase transformation is nucleation- the formation of very small particles or nuclei, of the new phase which are capable of growing. The second stage is growth, in which the nuclei increase in size; during this process, some volume of the parent phase disappears. The transformation reaches completion if growth of these new phase particles is allowed to proceed until the equilibrium fraction is attained. As would be expected, the time dependence of the transformations rate (which is often termed the kinetics of…
Precipitation reactions
A precipitation reaction is a reaction in which soluble ions in separate solutions are mixed together to form an insoluble compound that settles out of solution as a solid. That insoluble compound is called a precipitate
Particle strengthening by precipitation
The strength and hardness of some metal and alloys may be enhanced by the formation of extremely small uniformly dispersed particles of a second phase within the original phase matrix; this must be accomplished by phase transformations that are induced by appropriate heat treatments. The process is called precipitation hardening because the small particles of the new phase are termed “precipitates”. Precipitation hardening and the treating of steel to form tempered matrensite are totally different phenomena, even though the heat treatment procedures are similar.
Eutectoid and Peritectic Reactions
The eutectoid (eutectic-like) reaction is similar to the eutectic reaction but occurs from one solidphase to two new solid phases. It also shows as V on top of a horizontal line in the phase diagram. There are associated eutectoid temperature (or temperature), eutectoid phase, eutectoid and proeutectoid microstructures. The peritectic reaction also involves three solid in equilibrium, the transition is from a solid + liquid phase to a different solid phase when cooling. The inverse reaction occurs when heating.
Development of microstructure in eutectic alloys
Case of lead-tin alloys, A layered, eutectic structure develops when cooling below the eutectic temperature. Alloys which are to the left of the eutectic concentration (hipoeutectic) or to the right (hypereutectic) form a proeutectic phase before reaching the eutectic temperature, while in the solid + liquid region. The eutectic structure then adds when the remaining liquid is solidified when cooling further. The eutectic microstructure is lamellar (layered) due to the reduced diffusion distances in the solid state. To obtain the concentration of the eutectic microstructure in the final solid solution, one draws a vertical line at the eutectic concentration and applies the lever rule treating the eutectic as a separate phase.
Development of microstructure in isomorphous alloys
a) Equilibrium cooling Solidification in the solid + liquid phase occurs gradually upon cooling from the liquidus line. The composition of the solid and the liquid change gradually during cooling (as can be determined by the tie-line method.) Nuclei of the solid phase form and they grow to consume all the liquid at the solidus line. b) Non-equilibrium cooling Solidification in the solid + liquid phase also occurs gradually. The composition of the liquid phase evolves by diffusion, following the equilibrium values that can be derived from the tie-line method. However, diffusion in the solid state is very slow. Hence, the new layers that solidify on top of the grains have the equilibrium composition at that temperature but once they are solid their composition does not change. This lead to the formation of layered (cored) grains (Fig. 9.14) and to the invalidity of the tie-line method to determine the composition of the solid phase…
Grain size determination
The grain size is often determined when the properties of a polycrystalline material are under consideration. In this regard, there exist a number of techniques by which size is specified in terms of average grain volume, diameter, or area. Grain size may be estimated by using an interceptmethod, described as follows. Straight lines all the same length are drawn through several photomicrographs that show the grain structure. The grains intersected by each line segment are counted; the line length is then divided by an average of the number of grains intersected, taken over all the line segments. The average grain diameter is found by dividing this result by the linear magnification of the photomicrographs. Grain size is measured with a microscope by counting the number of grains within a given area, by determining the number of grains that intersect a given length of random line, or by comparison with standard charts. The average grain diameter…
Microstructural Exam
Microstructure is defined as the structure of a prepared surface or thin foil of material as revealed by a microscope above 25× magnification. The microstructure of a material can strongly influence physical properties such as strength, toughness, ductility, hardness, corrosion resistance, high/low temperature behavior, wear resistance, and so on, which in turn govern the application of these materials in industrial practice. a) Sectioning and cutting The areas of interest forming the metallography specimens need to be sectioned for ease of handling. Depending on the type of material, the sectioning operation can be done by using abrasive cutter (for metal and metallic composite), diamond wafer cutter (ceramics, electronics and minerals) …
Liquid-Penetration test
This test is employed for detection of small defects which are very small to detect with the naked eye. This test is used to detect surface cracks or flaws in non-ferrous metals. This test employs a visible colour contrast dye penetrant technique for the detection of open surface flaws in metallic and non-metallic objects. The penetrants are applied by spraying over the surface of material to be inspected. The excess penetrant is then washed or cleaned. Absorbent powder is then applied to absorb the penetrants in the cracks, voids which reveals the flaws. This test reveals flaws such as shrinkage cracks, porosity, fatigue cracks, grinding cracks, forging cracks, seams, heat treatment cracks and leaks etc., on castings, weldings, machined parts, cutting tools, pipes and tubes. If the fluorescent penetrant is used, the developed surface must be examined under ultra violet light to see the presence of defects. This technique is used for non-porous and non- absorbent materials. Care may be taken to clean the surface so that it is free from dust, scale, etc. to have better results. Penetrants are highly toxic and flammable and hence proper precautions should…
